Forum: 16v Engine Forum

Hi, I recently picked up a fully loaded NOS 16v head. To make a long story short I have little to no experience with building engines. I have an...

part number (bosch) 1 230 329 038 looks like this one in picture is there any place on internet from where I can order it, or any company. ...

Does this exist? I'm looking for a throttle body for driver side (Scirocco intake) with cruise control connections. When I installed the Scirocco...

I was disassembling my engine to due to low compression and found that I had a bout 1/8" or crank end play! It turns out that the crank ground away...

Just started collecting parts the engine will be a budget build, (yeah right). based on the PG engine from the G60 (this because i need the...

I have done few searches and I didn't find any topic on this subject, and by that i saw that there's topic with turbocharged 16v's and I tought that...

I am having a problem that I cant figure out. I have a 1992 GLI 16v that I do endurance racing with. after every day of racing, the bolts that hold...

http://a3.ec-images.myspacecdn.com/images02/1/a16017a2e01f41839f06e036b3054221/l.jpg Looking to get new polished or chrome socket hex caps. I...

http://blog.intengineering.com/wp-content/uploads/2013/05/HBEAMRODSSALE.jpg The Integrated Engineering ABA/ABF 159X20mm connecting rod is is the...

just a little forewarning, i'm almost done with swapping all this over. I have a full write up on the procedure.....should be done with in a week or...

Doesn't always start When it does start, run ok when cold, and most the time with no load once warmed up. Once warm, misfires really bad, can't...

I'll be glad to help

whats up everyone. I'm back, so of yous may remember me from "The Beast" 181whp on CIS-E back in 08... well I still have that car, but currently no...

I have had this idle problem on my boosted 9a engine for a while now.:banghead: When the engine gets warm it will rev from 1500 - 2000 repeatadly. ...

well i got a 2.0l 16v out of a 92 passat the motor is currently at the machine shop getting the block honed crank is getting polished and the deck of...

I'm having an issue getting my car to start. The past couple times i started it, it needed to be jumped. It would crank over and then the starter...

I've seen a few threads on here about people looking for Drake 16v heads for sale. In a nutshell, I worked at Drake in the early 1980's and I ran...

<FONT COLOR="red"><B><I>FINALLY THEY ARE DONE!!!</I>!!!!</B></FONT><p><FONT COLOR="green"><b>INTRO PRICES:<br>OIL PAN W/ STOCK GROUND CLEARANCE =...

So as I'm replacing a gasket on my oil filter flange (flange to block), I notice the dreaded "milky" oil. Just pulled my head and the headgasket...

As tittle says guys , My buddy wrecked my 337 . so i bought a shell .Owner told me after owning the car for one year , he could never get it to...

so i've been kicking around the idea of using fsi pistons in my NA 9a build. not so much for power,but for my everyday driver with excessive parts. i...

**********I was building an ITB setup but now going 16v g60 first 5 pages are my progress of the 16v ITB setup and im using some of the parts from...

Does anyone have a picture of a homemade test harness for the DPR? The ones I have found online are not very clear. I want to make sure that I am...

I had my 92 16v 2.0 Gti running perfectly fine, but eventually when i turned it off for 5 minutes, I tried to turn it back on and it didn't turn. ...

HI! }<br>I've been looking for the 16v sensors, I bought a head without them.<br>Hopefully you can help me to get ones (Mexico) or just the part...

Hey guys, recently acquired a PL 16v out of a scirocco that im planning on putting in my mk1, the engine has 138k, my question is about the timing...

Hi my friend has a 2L 16V abf clone that has been breaking distributor caps at high RPMs, literally splitting them into pieces with secure clamps....

Since there are a lot of new 16v turbo projects being built/rebuilt and some new parts coming out it's time for another ultimate 16vt info thread...

So slow at work. Post up threads on and car engine rebuild...good time to research and learn for my next 16v build!

Block is a 91 2.0 9A, miles unknown. Head is the original one from my 92 2.0 GLi. I plan on this taking awhile....3 kids, full time job,...