Discussion area for the G60 G-lader supercharged engine. This forum is sponsored by Bahn Brenner Motorsports.
Hello all-<p>I've started a collection of posts relating to subjects we commonly see in here and the Corrado forum. Rather than re-post it all in...
Hello everyone-<p>At the request of many of the long-time forum members, this thread is being created to serve as a place to rate the various G60...
Hey everybody.... I'd like to get some help for an FYI, FAQ my G60 runs like digifunk monkey spunk Q&A write up. <p>I didn't see this in the FAQ......
Hello everyone-<p>At the request of the masses, here's an FAQ for the g60 forum. For now, most of the content will be copied out of the FAQ in the...
THE “NEW” BBM G60 Twin Screw Supercharger Kit For Immediate Release: June 05, 2012 Sure the G60 is now considered old school cool, is BBM...
ANybody have any good tricks for getting the air out of the coolant system? I've never had any issue before, but this time I'm see 110c/230f with...
Feature Spotlight Don "The Repoman" Fritsche Old School Corrado. What is the definition of old school? Old school is a ride that shakes a...
I'll ask in this forum.. I spent a few hours searching, couldn't find the right post, but I'm sure this info is buried in there somewhere, I just...
these are the Gruvenparts.com ones. I tried to order but they dont have any. In order to get another run of them I/we need 9 more buyers, plus me to...
Any pit falls I should look out for? Or any helpful tricks for remove and replace speedo cable?
It looks like this thing was rebuild a couple of times. Last time may have been Motortechnik 7/2003 according to the most prominent markings. I...
Has anyone managed to find a source for replacement bushes for the g-lader belt tensioner damper?
on a g60 swapped gti should I use the g60 or 16v radiator?<br>Will the Golf fan and shroud work with a g60 radiator?<br>Searches and faq's haven't...
The Tao of the Hot Rodder By Repoman Hot rodding a car is going to cost you. Cutting corners will cost you more. if someone is faster than...
I'm rebuilding a G60 to put in my mk2 gti. I need a piston for the engine, and ive got an 8v 1.8l gti for parts. I havnt taken apart the engine on...
Has anybody swapped a o2a from a passat into your G60?? I just did and I'm having problems with the shift tower. The trans I just installed which was...
Guys, I am in need of some assistance. I've just acquired a '90 G60 with a rebuilt motor. Problem is it has no spark. The coil, distributor, rotor,...
Just found this site tonight and wanted to see if anyone had any experience with them? They seem to have a lot of options for cylinder head porting,...
i have a custom chip for 310 injectors but not sure on spec of pressure needed
So the mods balanced crank, 81.5mm cylinder bore with JE pistons, TT 260/268 cam, adjustable cam sprocket, valves, springs, lightened flywheel,...
I'm guessing stock! http://img.photobucket.com/albums/v488/kevinkovac/649A6BF6-0985-46DB-B844-0B84B5F65C67-13865-0000074B2E67B690_zps2a7533c7.jpg ...
In the process of trying to get my corrado on the road. I've come across an issue that has me a little stumped. It idles fine, a little rough on cold...
<U><FONT COLOR="orange"><B>EXTERNAL WATER PUMP BLOCK:</B></FONT></U><p><TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD><i>Quote,...
I beg your forgiveness for the possible incorrectness of the translation into English<p>start ...<p>we have:<br>1 CORRADO PG without...
i recently bought a 90 corrado g60. i ran into some ignition problems but now im good. i seem to have low boost issues. what are some common problems...
Hi, Looing for help in identifying this camshaft I have. The engine I purchased has the Neuspeed ISV and p chip kit w/ aluminum oil pan. I think...
Sent from my HTC One X+ using Tapatalk 2
I built this car almost 8 years ago. Rebuilding it. And getting it road worthy. http://img.tapatalk.com/c6e4e01d-0095-583a.jpg...
ROUND 3. I decided to make this thread after again getting quite a few PM's from members asking me to do a 16V G60 thread similiar to my 20V G60...
Hey guys I'm looking for a bit of help here with my G60 Rabbit I was driving a on Christmas Day December 25th and after a pretty long day of the...
This is the Official Order thread for the Billet G60 tensioners from GruvenParts.com. http://gruvenparts.com/website/imgs/fullsize/431.jpg ...
At TDC the mark on the intermediate shaft sprocket is out of time with the cylinder 1 mark on the distributor. What could cause this?...
Quick premise: Crank bolt snapped getting up to speed on interstate. Pulley key wasted and crank Key slot partially boogered.<p>here is my fix...
Thinking of ditching my crappy, loud, raceland header and starting a new exhaust from scratch. Is the g60 exhaust manifold the best manifold to bolt...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
